Yes, there is a restart capability in Elmer.
See chapter 3 of the solver manual
https://www.nic.funet.fi/pub/sci/physic ... Manual.pdf
Sign of Lorentz force
-
- Posts: 176
- Joined: 22 Mar 2021, 18:39
- Antispam: Yes
- Location: POLYTHECNIC UNIVERSITY OF TURIN
Re: Sign of Lorentz force
Hence, should I have done it since I defined the case.sif, right? Could I change the case.sif during the running?kevinarden wrote: ↑08 Jul 2021, 17:13 Yes, there is a restart capability in Elmer.
See chapter 3 of the solver manual
https://www.nic.funet.fi/pub/sci/physic ... Manual.pdf
-Andrea
POLYTECHNIC UNIVERSITY OF TURIN-DIMEAS
-
- Posts: 2313
- Joined: 25 Jan 2019, 01:28
- Antispam: Yes
Re: Sign of Lorentz force
Can't change the sif during the run. Have to define the restart file prior to doing the run.
-
- Posts: 176
- Joined: 22 Mar 2021, 18:39
- Antispam: Yes
- Location: POLYTHECNIC UNIVERSITY OF TURIN
Re: Sign of Lorentz force
Sorry if I bother you again, what is the third point? How may I get it?kevinarden wrote: ↑08 Jul 2021, 12:39 1. Get more RAM
2. Reduce the problem size
3. Set up/increase the size of a swap file (disk space used as RAM)
-Andrea
POLYTECHNIC UNIVERSITY OF TURIN-DIMEAS
-
- Posts: 2313
- Joined: 25 Jan 2019, 01:28
- Antispam: Yes
-
- Posts: 176
- Joined: 22 Mar 2021, 18:39
- Antispam: Yes
- Location: POLYTHECNIC UNIVERSITY OF TURIN
Re: Sign of Lorentz force
I have read that chapter, but Elmer keeps on giving an error. I attached case.sif and output. According to the case.sif, if, for instance, my simulation stops at 800/1000 time steps, can I restart it from that time step with the same results already obtained as for?kevinarden wrote: ↑08 Jul 2021, 17:13 Yes, there is a restart capability in Elmer.
See chapter 3 of the solver manual
https://www.nic.funet.fi/pub/sci/physic ... Manual.pdf
-Andrea
- Attachments
-
- output.txt
- (1.5 KiB) Downloaded 126 times
-
- case(3).sif
- (6.51 KiB) Downloaded 129 times
POLYTECHNIC UNIVERSITY OF TURIN-DIMEAS
-
- Posts: 2313
- Joined: 25 Jan 2019, 01:28
- Antispam: Yes
Re: Sign of Lorentz force
If the restart file was written for step 800 then you can restart from 800, if however it stopped during 800 before the restart data was written then you would have to restart from 799 or the lasted saved step in the restart file.
As far as the error Elmer is looking for a mesh named
/nobackup/st/palmarini/CASO/OSCILLAZIONI/CON
but you told it the mesh was in
Mesh DB "/nobackup/st/palmarini/CASO OSCILLAZIONI/CON CAMPO MAGNETICO/PROFILO TECHNICAL NOTES/DOMINIO_RIDOTTO_B=1" "mesh"
it appears it does not like blanks in the file name. Probably does not like the = sign either. I would replace these with _
As far as the error Elmer is looking for a mesh named
/nobackup/st/palmarini/CASO/OSCILLAZIONI/CON
but you told it the mesh was in
Mesh DB "/nobackup/st/palmarini/CASO OSCILLAZIONI/CON CAMPO MAGNETICO/PROFILO TECHNICAL NOTES/DOMINIO_RIDOTTO_B=1" "mesh"
it appears it does not like blanks in the file name. Probably does not like the = sign either. I would replace these with _
-
- Posts: 176
- Joined: 22 Mar 2021, 18:39
- Antispam: Yes
- Location: POLYTHECNIC UNIVERSITY OF TURIN
Re: Sign of Lorentz force
Now, I fixed the blanks spaces, bu it gave me always the same error.kevinarden wrote: ↑09 Jul 2021, 13:46 If the restart file was written for step 800 then you can restart from 800, if however it stopped during 800 before the restart data was written then you would have to restart from 799 or the lasted saved step in the restart file.
As far as the error Elmer is looking for a mesh named
/nobackup/st/palmarini/CASO/OSCILLAZIONI/CON
but you told it the mesh was in
Mesh DB "/nobackup/st/palmarini/CASO OSCILLAZIONI/CON CAMPO MAGNETICO/PROFILO TECHNICAL NOTES/DOMINIO_RIDOTTO_B=1" "mesh"
it appears it does not like blanks in the file name. Probably does not like the = sign either. I would replace these with _
-Andrea
- Attachments
-
- output.txt
- (3.67 KiB) Downloaded 126 times
-
- case.sif
- (6.45 KiB) Downloaded 128 times
POLYTECHNIC UNIVERSITY OF TURIN-DIMEAS
-
- Posts: 2313
- Joined: 25 Jan 2019, 01:28
- Antispam: Yes
Re: Sign of Lorentz force
Mesh DB "/nobackup/st/palmarini/DOMINIO_RIDOTTO_B=1" "mesh"
It may not like the =
It may not like the =
-
- Posts: 176
- Joined: 22 Mar 2021, 18:39
- Antispam: Yes
- Location: POLYTHECNIC UNIVERSITY OF TURIN
Re: Sign of Lorentz force
Nothing again. I attached the mesh that I am using. Could you try to run it please? Because, I don't understand what I am wronging. https://we.tl/t-drNNRZxPlckevinarden wrote: ↑09 Jul 2021, 15:19 Mesh DB "/nobackup/st/palmarini/DOMINIO_RIDOTTO_B=1" "mesh"
It may not like the =
Thanks and regards
Andrea
- Attachments
-
- case.sif
- (6.45 KiB) Downloaded 121 times
POLYTECHNIC UNIVERSITY OF TURIN-DIMEAS