To whom it may concern
I am new to Elmer. I want to model the gas flow by the pressure difference in the tube. I want to use the Perfect Gas model in Elmer. But I faced errors when I used the Perfect Gas model. I would be pleased if you help with this issue. I attached my SIF file for your reference.
Header
CHECK KEYWORDS Warn
Mesh DB "." "."
Include Path ""
Results Directory ""
End
Simulation
Max Output Level = 5
Coordinate System = Cartesian
Coordinate Mapping(3) = 1 2 3
Simulation Type = Steady state
Steady State Max Iterations = 10
Output Intervals = 1
Timestepping Method = BDF
BDF Order = 1
Solver Input File = case.sif
Post File = case.vtu
End
Constants
Gravity(4) = 0 1 0 9.82
Stefan Boltzmann = 5.67e08
Permittivity of Vacuum = 8.8542e12
Boltzmann Constant = 1.3807e23
Unit Charge = 1.602e19
End
Body 1
Target Bodies(1) = 1
Name = "Body 1"
Equation = 1
Material = 1
Initial condition = 1
End
Body 2
Target Bodies(1) = 2
Name = "Body 2"
Equation = 1
Material = 2
Initial condition = 2
End
Body 3
Target Bodies(1) = 3
Name = "Body 3"
Equation = 2
Material = 3
Initial condition = 3
End
Body 4
Target Bodies(1) = 4
Name = "Body 4"
Equation = 2
Material = 3
Initial condition = 3
End
Body 5
Target Bodies(1) = 5
Name = "Body 5"
Equation = 1
Material = 1
Initial condition = 3
End
Body 6
Target Bodies(1) = 6
Name = "Body 6"
Equation = 2
Material = 3
Initial condition = 3
End
Body 7
Target Bodies(1) = 7
Name = "Body 7"
Equation = 2
Material = 3
Initial condition = 3
End
Body 8
Target Bodies(1) = 8
Name = "Body 8"
Equation = 1
Material = 1
Initial condition = 4
End
Body 9
Target Bodies(1) = 9
Name = "Body 9"
Equation = 1
Material = 2
Initial condition = 5
End
Solver 3
Equation = Heat Equation
Procedure = "HeatSolve" "HeatSolver"
Variable = Temperature
Exec Solver = Always
Stabilize = True
Bubbles = False
Lumped Mass Matrix = False
Optimize Bandwidth = True
Steady State Convergence Tolerance = 1.0e5
Nonlinear System Convergence Tolerance = 1.0e7
Nonlinear System Max Iterations = 1
Nonlinear System Newton After Iterations = 3
Nonlinear System Newton After Tolerance = 1.0e3
Nonlinear System Relaxation Factor = 0.00001
Linear System Solver = Iterative
Linear System Iterative Method = BiCGStabl
Linear System Max Iterations = 500
Linear System Convergence Tolerance = 1.0e10
BiCGstabl polynomial degree = 2
Linear System Preconditioning = ILU0
Linear System ILUT Tolerance = 1.0e3
Linear System Abort Not Converged = False
Linear System Residual Output = 10
Linear System Precondition Recompute = 1
End
Solver 2
Equation = KEpsilon
Procedure = "KESolver" "KESolver"
Exec Solver = Always
Stabilize = True
Bubbles = False
Lumped Mass Matrix = False
Optimize Bandwidth = True
Steady State Convergence Tolerance = 1.0e5
Nonlinear System Convergence Tolerance = 1.0e7
Nonlinear System Max Iterations = 1
Nonlinear System Newton After Iterations = 3
Nonlinear System Newton After Tolerance = 1.0e3
Nonlinear System Relaxation Factor = 0.00001
Linear System Solver = Iterative
Linear System Iterative Method = BiCGStabl
Linear System Max Iterations = 500
Linear System Convergence Tolerance = 1.0e10
BiCGstabl polynomial degree = 2
Linear System Preconditioning = ILU0
Linear System ILUT Tolerance = 1.0e3
Linear System Abort Not Converged = False
Linear System Residual Output = 10
Linear System Precondition Recompute = 1
End
Solver 1
Equation = NavierStokes
Procedure = "FlowSolve" "FlowSolver"
Variable = Flow Solution[Velocity:3 Pressure:1]
Exec Solver = Always
Stabilize = True
Bubbles = False
Lumped Mass Matrix = False
Optimize Bandwidth = True
Steady State Convergence Tolerance = 1.0e5
Nonlinear System Convergence Tolerance = 1.0e7
Nonlinear System Max Iterations = 1
Nonlinear System Newton After Iterations = 3
Nonlinear System Newton After Tolerance = 1.0e3
Nonlinear System Relaxation Factor = 0.00001
Linear System Solver = Iterative
Linear System Iterative Method = BiCGStabl
Linear System Max Iterations = 500
Linear System Convergence Tolerance = 1.0e10
BiCGstabl polynomial degree = 2
Linear System Preconditioning = ILU0
Linear System ILUT Tolerance = 1.0e3
Linear System Abort Not Converged = False
Linear System Residual Output = 10
Linear System Precondition Recompute = 1
End
Equation 1
Name = "Just Heat"
Convection = Computed
Active Solvers(1) = 3
End
Equation 2
Name = "Heat+Navier+Kepsilon"
Convection = Computed
Active Solvers(3) = 2 1 3
End
Material 1
Name = "Steel"
Heat Conductivity = 10
Density = 8000
End
Material 2
Name = "Solid Mg"
Density = 1500
Viscosity = 0.0009
Heat Conductivity = 88
End
Material 3
Name = "Gas Mg"
Density = 0.01
Viscosity = 0.00088
Heat Conductivity = 85
Compressibility Model = Perfect Gas
End
Initial Condition 1
Name = "Bottom Steel"
Temperature = Variable " coordinate 3 "
Real MATC " 11233893.8 * tx "
Kinetic Dissipation = 1.0e4
Kinetic Energy = 0.00457
End
Initial Condition 2
Name = "Solid Mg"
Kinetic Dissipation = 1.0e4
Kinetic Energy = 0.00457
Temperature = Variable " coordinate 3 "
Real MATC " 1084442.5 *(tx0.01)
End
Initial Condition 3
Name = "Gas Mg"
Temperature = 1073.5
Kinetic Energy = 0.00457
Kinetic Dissipation = 1.0e4
End
Initial Condition 4
Name = "Top Steel"
Kinetic Dissipation = 1.0e4
Temperature = Variable " coordinate 3 "
Real MATC " 10733893.8 * (tx0.31) "
Kinetic Energy = 0.00457
End
Initial Condition 5
Name = "Top Solid Mg"
Kinetic Energy = 0.00457
Kinetic Dissipation = 1.0e4
Temperature = Variable " coordinate 3 "
Real MATC" 1034442.5*(tx0.32)
End
Boundary Condition 1
Target Boundaries(1) = 10
Name = "Bottom"
Temperature = 1123
End
Boundary Condition 2
Target Boundaries(2) = 16 41
Name = "Interface ( Solid/Gas)"
Pressure 3 = Variable " temperature "
Real MATC " exp(7750/(tx)+12.791.41*log(tx))*101300/760"
Heat Flux = Variable " velocity 3 "
Real MATC " 127400*24*0.01*tx "
End
Boundary Condition 3
Target Boundaries(11) = 17 24 26 28 29 30 35 36 37 38 39
Name = "Walls"
Noslip wall BC = True
End
Boundary Condition 4
Target Boundaries(1) = 46
Name = "Top"
Temperature = 1023
End
Elmer+Paraview

 Posts: 864
 Joined: 25 Jan 2019, 01:28
 Antispam: Yes
Re: Elmer+Paraview
what error does it report?

 Posts: 26
 Joined: 28 Jul 2020, 11:24
 Antispam: Yes
Re: Elmer+Paraview
Hello
Thank you for your reply.
the error is "
At line 4217 of file D:/ElmerBuilder/elmerfem/fem/src/Lists.F90
Fortran runtime error: Bad real number in item 1 of list input
Error termination. Backtrace:
Could not print backtrace: libbacktrace could not find executable to open
#0 0xffffffff
#1 0xffffffff
#2 0xffffffff
#3 0xffffffff
#4 0xffffffff
#5 0xffffffff
#6 0xffffffff
#7 0xffffffff
#8 0xffffffff
#9 0xffffffff
#10 0xffffffff
#11 0xffffffff
#12 0xffffffff
#13 0xffffffff
#14 0xffffffff
#15 0xffffffff
#16 0xffffffff
#17 0xffffffff
#18 0xffffffff
#19 0xffffffff
#20 0xffffffff
#21 0xffffffff
#22 0xffffffff
Thank you for your reply.
the error is "
At line 4217 of file D:/ElmerBuilder/elmerfem/fem/src/Lists.F90
Fortran runtime error: Bad real number in item 1 of list input
Error termination. Backtrace:
Could not print backtrace: libbacktrace could not find executable to open
#0 0xffffffff
#1 0xffffffff
#2 0xffffffff
#3 0xffffffff
#4 0xffffffff
#5 0xffffffff
#6 0xffffffff
#7 0xffffffff
#8 0xffffffff
#9 0xffffffff
#10 0xffffffff
#11 0xffffffff
#12 0xffffffff
#13 0xffffffff
#14 0xffffffff
#15 0xffffffff
#16 0xffffffff
#17 0xffffffff
#18 0xffffffff
#19 0xffffffff
#20 0xffffffff
#21 0xffffffff
#22 0xffffffff

 Posts: 864
 Joined: 25 Jan 2019, 01:28
 Antispam: Yes
Re: Elmer+Paraview
I don't think the variables should be in qoutes
Pressure 3 = Variable " temperature "
should be
Pressure 3 = Variable Temperature
Pressure 3 = Variable " temperature "
should be
Pressure 3 = Variable Temperature