Hi guys. I am using Salome.
I would like to ask you for some advices with creating multiple body insertion into Elmer. I am having one smaller box and one bigger box. The are "touching" with one side. It means the face of the bigger box touching the smaller box is only a section of the bigger box upper face.
I have tried to create multiple body model according to tutorial http://www.elmerfem.org/elmerwiki/index ... e_to_Elmer. But I did not obtain two bodies in Elmer.
Do I have to specify the contact face in any special manner?
Thank you very much for your time!!!
[SOLVED] Visualization of Multiple Bodies(3D) Generated from
[SOLVED] Visualization of Multiple Bodies(3D) Generated from
- Attachments
-
- twobox.png (17.69 KiB) Viewed 7763 times
Last edited by chatpall on 11 Dec 2014, 20:46, edited 1 time in total.
all about materials
materialing.com
materialing.com
Re: Two "box" problem
Hi,
could you post your Salomé study (or a python dump if it is too big)? If you create the geometry outside of Salomé, could you attach it? Then I can have a look at it and maybe find out what's wrong.
Matthias
could you post your Salomé study (or a python dump if it is too big)? If you create the geometry outside of Salomé, could you attach it? Then I can have a look at it and maybe find out what's wrong.
Matthias
Re: Two "box" problem
Hello Mattias,
I tried to attach salome file to the post, but with no success. How to attach it?
Thanks.
I tried to attach salome file to the post, but with no success. How to attach it?
Thanks.
mzenker wrote:Hi,
could you post your Salomé study (or a python dump if it is too big)? If you create the geometry outside of Salomé, could you attach it? Then I can have a look at it and maybe find out what's wrong.
Matthias
all about materials
materialing.com
materialing.com
Re: Two "box" problem
Hi,
principally you attach it in the same way you did for the picture above, except that you don't display it inline. If the file is larger than 2 MB, you can try to zip it. If it is still too large, then attach a Python dump of your study.
Matthias
principally you attach it in the same way you did for the picture above, except that you don't display it inline. If the file is larger than 2 MB, you can try to zip it. If it is still too large, then attach a Python dump of your study.
Matthias
Re: Two "box" problem
hi mattias,
i am trying to attach the file but with this note:
The extension hdf is not allowed.
i am trying to attach the file but with this note:
The extension hdf is not allowed.
all about materials
materialing.com
materialing.com
Re: Two "box" problem
zip it...
Re: Two "box" problem
so simple so far...
mzenker wrote:zip it...
- Attachments
-
- twobox.zip
- (626.58 KiB) Downloaded 579 times
all about materials
materialing.com
materialing.com
Re: Two "box" problem
Hi,
I do get two bodies in Elmer. Here is what I did:
1. open your study in Salomé
2. start SMESH
3. select Mesh_1
4. File->Export->UNV file
5. open Mesh_1.unv in ElmerGUI (File->open)
HTH,
Matthias
I do get two bodies in Elmer. Here is what I did:
1. open your study in Salomé
2. start SMESH
3. select Mesh_1
4. File->Export->UNV file
5. open Mesh_1.unv in ElmerGUI (File->open)
HTH,
Matthias
Re: Two "box" problem
Matthias I am sending a a video what my result of opening the file. I suppose there is some "mistake" in my compilation of elmer.
http://materialing.com/files/video.zip
Thank you very much for your time.
P.
http://materialing.com/files/video.zip
Thank you very much for your time.
P.
mzenker wrote:Hi,
I do get two bodies in Elmer. Here is what I did:
1. open your study in Salomé
2. start SMESH
3. select Mesh_1
4. File->Export->UNV file
5. open Mesh_1.unv in ElmerGUI (File->open)
HTH,
Matthias
all about materials
materialing.com
materialing.com
Re: Two "box" problem
Hi,
according to your video, you did the same as I did (except that I am under Windoze). I suspect a problem with your Elmer. If you zip your twobox.unv and post it here, I can see if my Elmer recognizes it correctly.
Matthias
according to your video, you did the same as I did (except that I am under Windoze). I suspect a problem with your Elmer. If you zip your twobox.unv and post it here, I can see if my Elmer recognizes it correctly.
Matthias