Search found 99 matches
- 05 Apr 2012, 12:04
- Forum: General
- Topic: Interpolation from Elmer results to a new Elmer mesh
- Replies: 7
- Views: 5854
Re: Interpolation from Elmer results to a new Elmer mesh
Hi, so, the question was: What happens if points do not coincide with the geometry their value is interpolated from? You might get some warning about points not being found in any of the elements. Check the result and choose, whether you are satisfied or not. As I understand, there are some toleranc...
- 05 Apr 2012, 09:59
- Forum: General
- Topic: Interpolation from Elmer results to a new Elmer mesh
- Replies: 7
- Views: 5854
Re: Interpolation from Elmer results to a new Elmer mesh
Hello, provided you have two meshes, mesh A and mesh B. easiest way would be to do a computation on mesh A, so Header Mesh DB "." "A" End and execute the first solver normally on this mesh. Solver 1 Equation = "the first solver" Variable = "VarA" ... End Then ...
- 07 Jan 2012, 13:16
- Forum: ElmerSolver
- Topic: can HeatSolver ignore the "Temperature" boundary condition?
- Replies: 3
- Views: 3306
Re: can HeatSolver ignore the "Temperature" boundary condition?
Hello, You can basically copy&paste the steady heat transfer solver from chapter 12 of the Solver Manual or try to modify the advection diffusion solver (model #3 in Models Manual). The issue - as I understand it from your previous message - is, that you need convection switched in for temperatu...
- 01 Sep 2011, 13:50
- Forum: Installation & compilation
- Topic: Easy compilation in Windows?
- Replies: 10
- Views: 14067
Re: Easy compilation in Windows?
Hi, the config.log should be directly in the sub-directory of the module source, where the compilation/configuration failed. For instance, when you spotted errors during compilation of the module fem, then check in fem/config.log My experience (on LINUX/UNIX platforms) with your error message "...
- 10 Aug 2011, 13:17
- Forum: Bug reports
- Topic: MUMPS workspace too small
- Replies: 5
- Views: 7159
Re: MUMPS workspace too small
I know that this reply is vastly delayed, but I think I insert this piece of information (beside the fact that it has been mentioned in the latest release notes) also here for those who are looking up this thread: The code lines Fabien suggested have been inserted and the corresponding MUMPS paramet...
- 17 May 2011, 08:35
- Forum: Installation & compilation
- Topic: MPI problem
- Replies: 5
- Views: 5287
Re: MPI problem
Hi,
could you perhaps check in Synaptic, whether you accidentally have hypre installed and hence the library within your paths? The config.log from the fem-directory would help to inquire that.
Regards,
Thomas
could you perhaps check in Synaptic, whether you accidentally have hypre installed and hence the library within your paths? The config.log from the fem-directory would help to inquire that.
Regards,
Thomas
- 05 May 2011, 13:13
- Forum: ElmerSolver
- Topic: Zeta potential not working?
- Replies: 10
- Views: 7250
Re: Zeta potential not working?
Dear Sebastian, on a first look I had I think there's something not OK with your mesh or I have issues in understanding what you are after. Three issues I found: 1) the left side boundary for me appears not to be defined all over the height (just load the mesh into ElmerPost and display all lines an...
- 04 Mar 2011, 16:14
- Forum: Events
- Topic: Summer Trainee Elmer
- Replies: 0
- Views: 7410
Summer Trainee Elmer
CSC is looking for a summer trainee to help implementing and develop Elmer modules for effective data I/O in parallel environments, in particular for climate related data stored in the NetCDF format. This includes automated interpolation data and coordinate transformation of coordinates. Time permit...
- 07 Jan 2011, 19:04
- Forum: Installation & compilation
- Topic: Problem compiling ElmerGUI on 64bit Fedora 14
- Replies: 7
- Views: 8104
Re: Problem compiling ElmerGUI on 64bit Fedora 14
Hello,
this is just a guess, but you might be in need of either setting the libraries in LD_LIBRARY_PATH or the LDFLAGS ...
Best wishes,
Thomas
this is just a guess, but you might be in need of either setting the libraries in LD_LIBRARY_PATH or the LDFLAGS ...
Best wishes,
Thomas
- 07 Jan 2011, 18:56
- Forum: ElmerPost
- Topic: Axisymmetric to 3D view
- Replies: 1
- Views: 3552
Re: Axisymmetric to 3D view
Hello,
to my information it is not possible to revolve axi-symmetric results inside ElmerPost. That would demand major modifications of the *.ep result file.
All the best,
Thomas
to my information it is not possible to revolve axi-symmetric results inside ElmerPost. That would demand major modifications of the *.ep result file.
All the best,
Thomas