Search found 8 matches
- 27 Mar 2019, 06:24
- Forum: Contributed Cases
- Topic: WhitneyAV 3D coupled current emag of a coil
- Replies: 14
- Views: 23663
Re: WhitneyAV 3D coupled current emag of a coil
Hello Everyone, I am using this module to generate magnetic field in 3D around a current carrying coil. In this the first solver being used is a STAT CURRENT SOLVER, where we apply some Voltage as boundary conditions. Is it possible to set a constant current in the coil instead of applying a voltage...
- 14 Sep 2018, 04:59
- Forum: ElmerSolver
- Topic: Converge on 1st iteration, then Nan in second?
- Replies: 1
- Views: 2579
Re: Converge on 1st iteration, then Nan in second?
Hi Einat,
Did you find any solution to this problem? I am also facing the same situation and have no idea why this happens !
Did you find any solution to this problem? I am also facing the same situation and have no idea why this happens !
- 13 Sep 2018, 12:00
- Forum: Contributed Cases
- Topic: WhitneyAV 3D coupled current emag of a coil
- Replies: 14
- Views: 23663
Re: WhitneyAV 3D coupled current emag of a coil
If this will help to find the error !!!!! **********Sif file Header CHECK KEYWORDS "Warn" Mesh DB "." "exportmesh" End Simulation Max Output Level = 9 Coordinate System = "Cartesian 3D" Coordinate Mapping(3) = 1 2 3 Simulation Type = Steady state Steady State ...
- 13 Sep 2018, 10:23
- Forum: Contributed Cases
- Topic: WhitneyAV 3D coupled current emag of a coil
- Replies: 14
- Views: 23663
Re: WhitneyAV 3D coupled current emag of a coil
Hi Mzenker and Raback,
Thanks for your help. The solver works fine using the cmd lines now. Just facing a new problem as shown below. Has anyone gone through the same???
Thanks for your help. The solver works fine using the cmd lines now. Just facing a new problem as shown below. Has anyone gone through the same???
- 13 Sep 2018, 09:38
- Forum: Bug reports
- Topic: MagnetoDynamics: Source current with StaticConduction, jfix
- Replies: 6
- Views: 8697
Re: MagnetoDynamics: Source current with StaticConduction, jfix
Can anyone give a clue of what might be going wrong and what else i can do ?
- 13 Sep 2018, 09:19
- Forum: Bug reports
- Topic: MagnetoDynamics: Source current with StaticConduction, jfix
- Replies: 6
- Views: 8697
Re: MagnetoDynamics: Source current with StaticConduction, jfix
Hi
I made the changes you suggested but i still get numerical error : IterSolve: System diverged over tolerance
I made the changes you suggested but i still get numerical error : IterSolve: System diverged over tolerance
- 11 Sep 2018, 06:08
- Forum: Contributed Cases
- Topic: WhitneyAV 3D coupled current emag of a coil
- Replies: 14
- Views: 23663
Re: WhitneyAV 3D coupled current emag of a coil
Hi Sometimes I remember that there was a problem with the very long runs (and the convergence plotter) when using GUI. Are you running the case using GUI? If yes, perhaps you could try using command line. -Peter Hi raback I am using elmer 8.0 on windows 7 and as you pointed out I was using GUI for ...
- 10 Sep 2018, 10:51
- Forum: Contributed Cases
- Topic: WhitneyAV 3D coupled current emag of a coil
- Replies: 14
- Views: 23663
Re: WhitneyAV 3D coupled current emag of a coil
Hi Daniel, I have recently started using Elmer for generating the magnetic field around a current carrying coil. I was using your example as a reference to understand the working. I am able to run your files as you mentioned in your post to generate the results. However, the Elmer software crashes e...